News

Product quality requirements - Bonsai pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, it can be repaired. 10. The feet should be flat and free of cracks, and the feet can be repaired except for small cracks. The inner cavity should be clean and free of debris. 11. With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. Control the size and weight of the product. 2: Refining basin 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, it can be repaired. 10. The feet should be flat and free of cracks, and the feet can be repaired except for small cracks. The inner cavity should be clean and free of debris. 11. With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 12. The inside of the basin should be clean, with uniform length and direction of fine lines, and all four legs should be flat Control the size and weight of the product. 3: Orchid pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, except for those that can be repaired. 10. With brackets: The color of the brackets should be basically the same, the brackets should be fully glazed, the brackets should not be too small, and the proportion should be moderate. 11. The inside of the basin should be clean and free of mud and debris, and the walls should be clean. The flower picking area should be neatly organized and not pricked. The flower picking pattern should meet the requirements of the sample, and the size and weight of the product should be controlled. 4: Moisturizing basin 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired. 10. The inner cavity should be clean and free of debris. Ensure that the inner liner is permeable, the outer shell is not leaking, and the inner liner sleeve outer shell has some gaps that can rotate smoothly. Control the size and weight of the product. 4: Diandian Pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass) The bottom is cracked and not penetrated, and repair can pass. 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired by 10 With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 11. The inner cavity should be clean and free of debris. Make every point clear and have a sense of unevenness. Control the size and weight of the product. 5. Blank type 1. Cracking: The edge of the product. (No matter the inner or outer opening, it is not allowed to pass) The bottom is cracked and not penetrated, and repair can pass. 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired by 10 With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 11. It is required that the bottom of the basin be cut off, the bottom of the basin be clean and free of mud debris, the cut off area should be smooth, the edge holes should be round, and the basin holder should not deviate. Glazing should be done in place (especially in the area between the basin supports), and the second batch should not pass through. If it is a two-piece or three-piece set, it must be done well, and it should not exceed the height of the six handmade types (including even pottery pots) The mouth surface cracks and does not penetrate properly, and repair can pass 2 The large basin has vertical or horizontal openings around it. If it doesn't break, it can pass 3 The bottom cannot be nailed or missing meat. It can be repaired, but it should be flat and not exceed the visible surface at the bottom Impurities do not prick hands, have a small area, and are not dense enough to pass through. The shrinkage area is small and not dense, which can be repaired (10-14 "can have 2 to 3 places, the whole body cannot exceed 3 places, 18-24" can have 3 to 4 places, the whole body cannot exceed 4 places) 5 The deformation can pass within the range of ± 4% for 10-14 "and ± 5% for 18-24" The patterned and dotted lines should be clear, and the lines should be clear. The Haff line should not be clearly glazed, and the large pot should be in place with neat lines and edges. There should be no missing glaze, thin glaze, or thick glaze attached. Packaging quality requirements: 1 The size of the cardboard box should meet the requirements, and the cardboard box should be clean and tidy with a clear description The incoming product should be clean and dust-free. Stick the foot in place, stick the barcode well, and label the cardboard box product with one variety, one color, and one pallet. It is absolutely not allowed to exceed two varieties and two colors (except for special cases, such as self use pots, except for special small orders). 3. The manual pot packaging must be in place, and the paper or soft strips inside the pot must be in place to prevent collisions between pots. The upper pot must be separated from the pot by cardboard, and the inverted pot must be placed with more paper or soft strips to prevent collisions when holding the pot.

Modern development and innovation Since the 20th century, the development of Yixing ceramic bonsai pots has undergone several significant changes. With the advancement of technology and changes in market demand, Yixing ceramic craftsmen continue to innovate and produce various ceramic bonsai pots that meet modern aesthetic and usage needs. Since the reform and opening up (after 1978), the ceramic industry in Yixing has ushered in new development opportunities. The combination of traditional craftsmanship and modern technology has made the variety and quality of Yixing ceramic bonsai pots more diverse. Modern Yixing ceramic bonsai pots not only include traditional purple clay pots, but also various glazed ceramic pots, meeting the needs of different consumers. Characteristics of Yixing Ceramic Bonsai Pots Diverse shapes and designs: Yixing ceramic bonsai pots have diverse shapes, ranging from traditional minimalist styles to modern creative designs. Exquisite glaze color: Using high-temperature firing technology, the glaze color is bright and rich, with various colors and textures. High quality materials: Select high-quality clay to ensure the durability and aesthetics of the product. The combination of handcrafting and mass production: there are both handicrafts meticulously crafted by craftsmen and cost-effective products manufactured by modern production lines. Current Market and Future Today, Yixing ceramic bonsai pots have a high reputation in both domestic and international markets, and are loved by horticultural enthusiasts and collectors. With the continuous improvement of people's pursuit of horticulture and aesthetics of life, Yixing ceramic bonsai pots are also constantly developing and innovating, demonstrating strong vitality. In the future, Yixing Ceramic Bonsai Pots will continue to uphold traditional craftsmanship and combine modern technology to launch more high-quality products that meet market demand, continuing to lead the development trend of ceramic art.

Our company has always focused on designing and manufacturing high-quality ceramic handicrafts. We have improved several models of ceramic bird feeders. We have made the following enhancements to the previous design: Improved design: We have improved the shape of the bird and feeder to make the bird look more realistic and ensure better fit between the bird and the feeder. This solves the problem of birds being easily separated. High quality glaze: Our ceramic glaze is made by special formula and high-temperature firing to ensure a smooth and uniform surface. This makes the feeder hole free, easy to clean, and highly durable.

I believe that a large part of people in daily life like to raise flowers, and put various styles of flowers at home to decorate. At this time, if you have a good pot tray, it will be better, and you can make plants more Good growth, and can be decorated in a stylish and elegant style. Because there are so many kinds of flower pots nowadays, how to configure the appropriate flowerpot tray ? Then let Xiaobian take everyone to find out. 1. In the market, I think everyone should know that it is a plastic flower pot tray, because the cost of the plastic vase tray is very cheap, and it is convenient. However, the plastic vase tray can only be an "emergency basin". Everyone knows that plastic is polycarbonate, impervious to water and airtight. This is sometimes the case when we see the yellow leaves. Not water is not enough, it may not be airtight. 2. Plants that grow in plastic pots for a long time may cause poor growth or even death due to restriction of root respiration; as well as plastics that are cracked in the sun, and plastics are also aging, emitting toxins and harming The health of plants and humans is not good for the environment. Therefore, after purchasing the plants, the plants should be replanted into pots of other materials to grow flowers and plants. 3. When choosing a plastic vase tray, if you want to go to someone else's house to transplant some flower varieties and plants, buy a plastic basin, go home, wash the water for a month or three months, you really need to change the basin. Because, at that time, the flowers are not strong, they can only be barely maintained, so it will not look good. 4. Flowerpot tray basin, this basin, we all especially use the flowerpots that our parents use at home. This flowerpot has good permeability and strong water permeability, which is good for plant growth. However, because this material is not suitable for shaping, the shape of the tile is generally not very good, and the viewing is also general, and the basin of this material is easy to be soiled with ash, not very clean, so the tile has been Rarely seen in the market, and occasionally seen in traditional homes. 5. If you have any pots and trays, continue to use them. It is also good. It is very good for plants. This is a bit like a virtuous person. The appearance is flat but the heart is very kind and beautiful. It can be used for a long time. of. The flower pot plants in the parents' home are well proven. 6. Flowerpot tray Porcelain basin If you have a good flower or a good plant at home, you can use one, but if it is a simple flower, you will not use the porcelain pot for the time being, because you have to change the basin. At the time, use the porcelain pot. At that time, the plant should be a strong period. It will be strong against various germs and strong in resistance. Then use the porcelain pot. The flower will be very good and beautiful. The porcelain basin is ok.